See also:
- MID216 Volvo LCM outdoor lighting control unit fault codes
- MID214 Volvo burglar alarm control unit fault codes
MID 219 SID 1
Parameter:
ACC Radar
Fault:
FMI 13Radar misdirected.The radar is installed with offset or damaged radar mount.
MID 219 SID 2
Parameter:
ACC Radar
Fault:
FMI 3The ACC control unit receives a message that a voltage higher than 12 V is applied to the radar. The radar supply wire is shorted to a circuit with a higher voltage or the exchange stability sensor A75 is faulty.
FMI 4The ACC control unit receives a message that the radar is under voltage below 12 V. An interruption in the power cord, a short in the power cord to ground or a course stability sensor A75 is faulty.
FMI 12The ACC control unit receives a message that one of the radar components is faulty.Internal radar malfunction.
MID 219 SID 231
Parameter:
SAE J1939 data feed
Fault:
FMI 2ACC control unitdoes not receive messages over SAE J1939 data channel.Damaged or oxidized pins in connectors or broken data channel wires.
MID 219 SID 240
Parameter:
Program memory
Fault:
FMI 2Software failure or defective storage circuit in the ACC unit.
MID 219 SID 248
Parameter:
Data Channel SAE J1939 CAN6 (internal channel)
Fault:
FMI 2The ACC control unit registers a failure of the internal data channel CAN6 (data channel between the ACC unit and the radar).Damaged or oxidized pins in connectors or broken data channel wires.
FMI 12The radar does not respond to requests from the control unit ACC on the internal data channel.Faulty data channel.
MID 219 SID 250
Parameter:
SAE J1708 data feed
Fault:
FMI 2The control unit ACC registers the error messages in the data channel.Perhaps several control units simultaneously send messages.
MID 219 SID 253
Parameter:
Gauge memory, EEPROM
Fault:
FMI 2A programming error or a bad memory circuit in the ACC unit.
MID 219 PSID 1
Parameter:
ACC Radar, Radiation
Fault:
FMI 1The ACC control unit received a message that the radar does not emit in the microwave.Internal radar malfunction.
MID 219 PSID 2
Parameter:
ACC system radar, reception
Fault:
FMI 0The control unit of the ACC received a message about interference with the radar.Eliminate interference, check fault codes.
FMI 1The control unit ACC received a message that the radar is closed by a foreign object.Remove foreign objects, check fault codes.
MID 219 PSID 3
Parameter:
ACC Radar Temperature
Fault:
FMI 0The ACC control unit received a message that the radar temperature is above normal.Internal radar malfunction.
FMI 1The control unit ACC received a message that the temperature of the radar is below normal.The internal radar heater does not work.Replace radar unit.
MID 219 PSID 4
Parameter:
ACC system radar calibration
Fault:
FMI 2The control unit of the ACC received a message about the incorrect calibration of the radar.The radar is displaced from its place or not calibrated.
MID 219 PSID 6
Parameter:
Stability Sensor
Fault:
FMI 3The voltage on the PB8 contact of the ACC unit from the sensor is higher than 4.5 V. The wiring between the ACC unit and the sensor is faulty or the sensor is faulty.
FMI 4The voltage on the PB8 contact of the ACC unit from the sensor is below 0.5 V. The wiring between the ACC unit and the sensor is faulty or the sensor is faulty.
MID 219 PSID 7
Parameter:
Stability sensor, power
Fault:
FMI 3The voltage on the PB9 terminal of the ACC unit from the sensor is higher than 2.6 V. The voltage converter is faulty.
FMI 4The voltage on the PB9 terminal of the ACC unit from the sensor is below 2.3 V. The voltage converter is faulty.
MID 219 PSID 8
Parameter:
Cruise control switch, time interval
Fault:
FMI 12The control unit ACC registers the signals from the key to increase and decrease the time interval simultaneously.The wiring between the ACC control unit and the switch is faulty or the switch is faulty.
MID 219 PSID 9
Parameter:
ACC system radar operating mode
Fault:
FMI 1The control unit ACC received a message that the radar is in the launch phase.External interference when launching a radar.Stop the car for 15 seconds, so that the radar will repeat the launch.
MID 219 PSID 11
Parameter:
Miscellaneous software in the ACC control unit and radar
Fault:
FMI 2Error in the programming process.An ACC control unit or radar is installed without installing the correct software.
MID 219 PSID 12
Parameter:
Data Channel SAE J1939 CAN6
Fault:
FMI 9The ACC control unit does not receive messages over the data channel.Data channel wiring malfunction, contacts in connectors are oxidized or damaged.
MID 219 PSID 200
Parameter:
Data Link DisruptionSAE J1939 with engine control unit MID128
Fault:
FMI 9The ACC control unit does not receive signals from the MID128 engine control unit via the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
MID 219 PSID 201
Parameter:
Data Link DisruptionSAE J1939 with car control unit MID144
Fault:
FMI 9The ACC control unit does not receive signals from the car control unit MID144 via the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
MID 219 PSID 202
Parameter:
Data Link DisruptionSAE J1939 with dashboard control unit MID140
Fault:
FMI 9The ACC control unit does not receive signals from the MID140 dashboard control unit over the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
MID 219 PSID 205
Parameter:
Data Link DisruptionSAE J1939 with MID130 gearbox control unit
Fault:
FMI 9The ACC control unit does not receive signals from the MID130 transmission control unit over the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
MID 219 PSID 206
Parameter:
Data Link DisruptionSAE J1939 with a MID222 retarder control unit
Fault:
FMI 9The ACC control unit does not receive signals from the retarder control unit MID222 via the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
MID 219 PSID 208
Parameter:
Data Link DisruptionSAE J1939 with air suspension control unit MID150
Fault:
FMI 9The ACC control unit does not receive signals from the MID150 air suspension control unit via the SAE J1939 data channel.Breakage or partial damage to the wires of the data channel between the blocks.
